（不推荐，请谨慎购买，需要刷机）一个“老”神猫，Thomson TG782T

yesngo

谢谢，一周没有短线了

szmao

商务车 发表于 2012-12-27 21:08
我刷的名称是： dant-d_AZ-retail.rbi

具体可以看这里：http://forums.whirlpool.net.au/archive/121632 ...

我也是刷的 dant-d_AZ-retail.rbi，但是我还是用不了其他家的网络。

不知道你是怎么刷的，能说一下吗？谢谢。

stccs111

szmao 发表于 2013-6-2 17:06
我也是刷的 dant-d_AZ-retail.rbi，但是我还是用不了其他家的网络。

不知道你是怎么刷的，能说一下吗？ ...

我也是刷了但上不了IINET，照说法是得焊几跟线接特别的串口线解锁，我放弃了

商务车

szmao 发表于 2013-6-2 17:06
我也是刷的 dant-d_AZ-retail.rbi，但是我还是用不了其他家的网络。

不知道你是怎么刷的，能说一下吗？ ...

我家用tpg，没办法实验其他isp的网络，不好意思。

richsea

是你们的用户名输得不对，要在账号后加@bigpond.com

szmao

richsea 发表于 2013-6-2 17:40
是你们的用户名输得不对，要在账号后加@bigpond.com

我用的不是bigpond的网络， 也不是tpg。就是想知道你们的刷价方法。

szmao

商务车 发表于 2013-6-2 17:39
我家用tpg，没办法实验其他isp的网络，不好意思。

你能给个刷机的步骤吗、。谢谢。

richsea

szmao 发表于 2013-6-2 17:55
我用的不是bigpond的网络， 也不是tpg。就是想知道你们的刷价方法。

你有在用户名后面加上试过了么？

szmao

richsea 发表于 2013-6-2 18:04
你有在用户名后面加上试过了么？

没有明白， 能说的具体些？

用户名不是你自己的网络用户名吗？

商务车

获取root权限：
telnet xxxx
admin
blank

:script add name addroot command "user add name guru password guru role root descr ROOT"
:script run name addroot pars ""
:saveall

{guru}=>user config name=admin role=root defuser =enabled
{guru}=>saveall

:cwmp config state=disabled
saveall

==============================================================


TG782T - unlocking VOIP & other features
first: 3 years ago1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 last: 20 hours ago
User #25496   35735 posts
Revs Per Min
Darth Rayder. breathe in . out
Whirlpool Forums Addict
http://whrl.pl/RcKx4i
herring | anchor
Reply to this post | Send whim
posted 2011-May-12, 8:27 am
edited 2011-Sep-18, 9:02 am
this post was edited
Let me report success!!

Please before using this method read and re-read the instructions.. most issues are people are not reading the full instructions and paying attention to every part. There is some issue as well with root access so please note that.

Use a TG782T with any ISP plus voip.. Instructions only for voip ports model.. board number DANT-D.. if you have a new DANT-W no voip ports you will still need to jtag it (I did try to jtag and modify the firmware on W board and still couldn't get it to work on none Telstra ISP.. didn't waste a lot of time trying to be truthful but just don't buy them.)

Alex Kemp has made available on his website some firmware for the TG782T, 8.6.P.1 in both an ISP and a Retail version. It is xxx.rbi which is supposed to be installed via ACS server.. and I seem to have taken that too literally.. ruining one pc OS install trying to run OpenACS and getting nowhere at all.

Anyway, in the midst of these experiments I thought I might be able to see what is happening when one of these firmware is loaded via the normal update wizard.. surprise surprise.. it not only uploaded fine, it upgraded the firmware. All my bashing away has been washed away by a simple straight normal update.

I have so far checked upgrade from 8.2.3 firmware and 8.6.F and it worked fine in both cases.
So far it looks like the retail firmware is still locked to Telstra.. but the ISP firmware is actually unlocked. So you can use it with any ISP. You will need to use sleepdeprived's script still to get voip working but it does.

Edit 1 Sept '11 There is new firmware up to 8.6.P.3 you will now find here.
http://download.modem-help.co.uk ... /Firmware/r8-6-S-1/
The AV and AW firmware seems no different to the previous one, but there is a new BA-ISP which is the latest one.. it flashes fine.. but don't do it until I test if works.

Edit 2 Sept '11 WARNING.. I have hit a snag with getting root access. This has now happened on 2 modems out of about 7 or 8. The error is mentioned here that the script loads fine but will not run.
{admin}=>script run name addroot pars ""
[mlp] Invalid/duplicate username or user database full.

I have been working hard to find out why and/or a work around and nothing has worked. I am not sure of the sequence, but let me warn people, do the root access on the original firmware. It may not fix the issue, but at least you will know it is going to happen. That will prevent using the voip. It can still work on a third party ISP. I tested with Alex's latest setup wizard and it also fails to get root or su access. I might have updated firmware before getting root.. but haven't had the problem before even post update firmware. It isn't specific to a bootloader or serial number. I have two boxes very close in serial and otherwise identical. One works and the other doesn't.

Upgrade firmware to 8.6.P.1 for any ISP

1. You need to set a static IP on your pc, eg 192.168.1.100 with no gateway or dns being required. Turn off firewalls and some Antivirus can also be troublesome. ie anything made by symantec. (note using 10.0.0.x failed to find the modem on reboot.. it is expecting the wizard to respond on 192.168.1.x subnet)

2. Download the firmware.
http://download.modem-help.co.uk ... /Firmware/r8-6-P-1/

3. Download the upgrade wizard.
http://download.modem-help.co.uk ... ms/Wizards/Upgrade/

4. Unpack both in a suitable directory. And run the wizard.. put in your username .. admin and leave password blank. (if this doesn't work create a new user in the tool box.. fredblogs and it will have password identical to the name.)
Once you do that it should just upgrade.

5. At the end of the upgrade the wizard again asks for the username and password but doesn't accept any valid ones.. just cancel.. you are finished.

YMMV.. warning.. one TG782T died to bring you this info. I doubt you will destroy your modem.. but expect no help from Telstra if you do. They are cheap as blazes on ebay.. just buy another one.. as I don't have several hours to jtag it for you.

I have tried two modems and it worked... sleepdeprived has also tested it on one modem with both firmware. I also killed one modem (but it has jtag and was the testbed for 8.6.P.3 off the latest TG782T without voip so it has some excuse to die).

Please post your experience but only whim me if you want to provide me a modem with 8.6.P.3 or you want to use the usb method to extract the mtd and email it to me.
see http://download.modem-help.co.uk ... P-Usage-v1.1.7z.php
This requires getting telnet access to the busybox and copying the flash to usb stick. It isn't easy and seems to fail more than succeed.

Root access to enable voip
Just to make this post complete.. when you finish the loading of the firmware. Then unlock the rights to the admin user.. by first running sdp's script. You have to login via telnet as admin (password blank) and copy and paste the commands perhaps via notepad incase the lines break.

:script add name addroot command "user add name guru password guru role root descr ROOT"
:script run name addroot pars ""
:saveall

Enable root privileges for admin user
Exit the cli and log back in with user guru and password guru.
Now you can change the admin to also have root privileges.
{guru}=>user config name=admin role=root defuser =enabled
{guru}=>saveall

Now open the gui or refresh the page and Telephony will appear in the Toolbox.

Disable CWMP if your config is wiped
And what fun.. each time I connect I have telstra update my settings.. yeah for telstra. I have now got a user on the telstra network as my username and their password.
In the log it shows,
May 12 08:38:48        CONFIGURATION saved by TR69

So telnet into the cli again and disable cwmp
:cwmp config state=disabled
saveall

That should stop the continual change of user.. amazing this old box must still have the original owner registered.. anyway I am using it with my ISP.. praise the maker.. not Telstra.

voip setup
The voip is all there.. but so far has resisted registering.. sigh!!
Ok I missed filling in proxy as well as main register.. so make sure you fill in both.. and most likely they are the same. Now everything is working.

so under configure.
Telphone (sic) Identity

Telephony Identity

SIP URI:        0925xxxxxx etc.
Username:         0925xxxxxx etc.
Password:        xxxx
Confirm Password: xxxx       
Displayname:        0925xxxxxx etc.
Abbreviated number:       
Port:        all

Under expert configure

Telephony

Service Configuration

Registrar:        sip00.mynetfone.com.au (put in your VSP URL)
Registrar Port:        5060
Proxy:        sip00.mynetfone.com.au (put in your VSP URL) this is required
Proxy Port:        5060
Secondary Proxy:        0.0.0.0
Secondary Proxy Port: 5060       
Expire Time:        3600

dhcp if unique
One other strange one.. if you use a different IP address.. the new configuration page leaves out the local gateway.. and preserves the old one. So you can reset the TG home IP and the dhcp range.. but the gateway stays as it was.. so I change to 192.168.2.x and the gateway is still 192.168.1.x. You will need to go into the cli and change the dhcp server local address. This worked better in the old firmware where you specifically set the gateway. 2 steps forward — at least 1 back.

Edit.. Also note Alex has a PC setup wizard which will give you root or superuser access but you will need to run through it once then change over user to su with password su. This is instead of using the telnet option.
http://forums.modem-help.co.uk/v ... 850a8a0609e26158c97

商务车

tg782t 默认qos规则
[ labelrule.ini ]
chain add chain=rt_user_labels
chain add chain=rt_default_labels
chain add chain=qos_user_labels
chain add chain=qos_default_labels
rule add chain=qos_default_labels index=1 serv=h323 log=disabled state=enabled label=VoIP-Signal
rule add chain=qos_default_labels index=2 serv=sip log=disabled state=enabled label=VoIP-Signal
rule add chain=qos_default_labels index=3 serv=ah log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=4 serv=esp log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=5 serv=http log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=6 serv=httpproxy log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=7 serv=https log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=8 serv=imap log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=9 serv=imap3 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=10 serv=imap4-ssl log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=11 serv=imaps log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=12 serv=pop2 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=13 serv=pop3 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=14 serv=pop3s log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=15 serv=smtp log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=16 serv=telnet log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=17 serv=dns log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=18 serv=icmp log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=19 serv=ike log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=20 serv=igmp log=disabled state=enabled label=Video
rule add chain=qos_default_labels index=21 serv=rtsp log=disabled state=enabled label=Video
rule add chain=qos_default_labels index=22 serv=DiffServ log=disabled state=enabled label=DSCP
rule add chain=qos_default_labels index=23 name=default srcintf=!wan log=disabled state=enabled label=default

商务车

OQS真是个好东西，而且在网络方面如果精通任何一个厂家的qos都是很牛的人物了。

附件是tg782t的qos配置指南，非常复杂，感兴趣的可以下载看看。

stccs111

richsea 发表于 2013-6-2 18:04
你有在用户名后面加上试过了么？

请问是IINET的用户也@bigpond.com吗？
IINET与TPG不一样，不走TELSTRA的线路
不管怎么样，我试试再说，谢谢

金陵悠游

ebay上1.25拍到一个，运费花了13.5，囧
昨天刷了解锁固件，工作在TPG网络还不错
外接了一个U盘开启了内网文件共享，还开通了外网FTP服务

不知道还有啥能折腾的。稳定性有待考验。
我一般24小时开机，不知道能hold多久。另外很想看看刮风下雨的时候会不会掉线

商务车

金陵悠游 发表于 2014-5-30 10:15
ebay上1.25拍到一个，运费花了13.5，囧
昨天刷了解锁固件，工作在TPG网络还不错
外接了一个U盘开启了内网文 ...

兄弟动手能力很强，也是做网络的吧？
话说外网ftp怎么开我一直没弄。
还有voip功能阿这个是用它的主要目的。

金陵悠游

商务车 发表于 2014-5-30 10:55
兄弟动手能力很强，也是做网络的吧？
话说外网ftp怎么开我一直没弄。
还有voip功能阿这个是用它的主要目 ...

我是码农，网络懂得不多，主要爱折腾
FTP服务器默认操作是开不了的，需要telnet进去改点东西
google了一个教程，对着做就好了

https://www.youtube.com/watch?v=iZMmKl1Fl7o

VOIP TPG有啥好台吗？

金陵悠游

商务车 发表于 2014-5-30 10:55
兄弟动手能力很强，也是做网络的吧？
话说外网ftp怎么开我一直没弄。
还有voip功能阿这个是用它的主要目 ...

对了，这个能刷OpenWrt吗？硬件看起来很不错，还有USB口。唯一的短板是54M，不过足够应付一般的ADSL2+速度了

商务车

金陵悠游 发表于 2014-5-30 11:24
对了，这个能刷OpenWrt吗？硬件看起来很不错，还有USB口。唯一的短板是54M，不过足够应付一般的ADSL2+速 ...

当然不能
能刷wrt的几乎都是没有modem功能的无线路由器

chatdm

这个能当dummy modem用吗？直接bridge mode，连其他的router?

商务车

chatdm 发表于 2014-5-30 14:19
这个能当dummy modem用吗？直接bridge mode，连其他的router?

现在不用这个设备了，但是觉得不能。

staples

Broadcom的芯片对离exchange远的的确在稳定性上有很大帮助。离exchange比较近（whirlpool标准2KM）不必纠结这个。我之前买了个华硕N12U，下载速度比W8960N快但有时会断线，如果离exchange近的不妨可以一试。

金陵悠游

chatdm 发表于 2014-5-30 14:19
这个能当dummy modem用吗？直接bridge mode，连其他的router?

这样是算支持bridge mode吗

金陵悠游

staples 发表于 2014-5-30 15:45
Broadcom的芯片对离exchange远的的确在稳定性上有很大帮助。离exchange比较近（whirlpool标准2KM）不必纠结 ...

我离得比较远

白雲山民

感谢分享v

whitecats

这产品好多年前的了吧

idog8818

whitecats 发表于 2014-8-27 08:48
这产品好多年前的了吧

楼上胖妹挖老坟?

whitecats

idog8818 发表于 2014-8-27 10:38
楼上胖妹挖老坟?

这坟才3个月哦

Hugh_King

我按图索骥，买了TG782T,用的是TPG的网络，请问各位如何修改用户名？我自己卡在“用户名和密码错误”。

Hugh_King

我按图索骥，买了TG782T,用的是TPG的网络，请问各位如何修改用户名？我自己卡在“用户名和密码错误”。

商务车

Hugh_King 发表于 2014-11-15 05:59
我按图索骥，买了TG782T,用的是TPG的网络，请问各位如何修改用户名？我自己卡在“用户名和密码错误”。  ...

这么老的产品你买它干嘛啊？

不好意思我周末在外面，没办法回答你具体的步骤。
主要是通过命令行打开管理员权限，然后，再重新登陆主菜单就可以改用户名了，还有voip的选项也可以出来了。

具体你可以搜索一下，很简单只有几步。