新足迹

 找回密码
 注册

精华好帖回顾

· 长篇连载--忽尔十年(#223精彩更新,#102有pp的封面) (2009-2-15) 哈他真的生气了 · 让第二代在澳洲快乐的成长 (2008-5-6) 风玲
· My Skincare with Obagi (2005-1-8) chubbycat · 美食版+数码版联合活动《水果》: 水,水果的水。26# 新增一组。 (2008-11-15) Tiger_Karen
Advertisement
Advertisement
查看: 842|回复: 10

[汽车咨讯] Qualified mechanic 解答car service方面的问题 - 欢迎提问! [复制链接]

发表于 2010-12-31 21:01 |显示全部楼层
此文章由 elsewhere 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 elsewhere 所有!转贴必须注明作者、出处和本声明,并保持内容完整
I have years of experience working on Janpanese cars including Toyota, Subaru, Mitsubishi and Honda. Happy answer your enquiries regarding servicing cost, tyres, oil and so on.

[ 本帖最后由 elsewhere 于 2011-1-1 20:45 编辑 ]
Advertisement
Advertisement

退役斑竹 2008年度奖章获得者

发表于 2010-12-31 21:04 |显示全部楼层
此文章由 dickson 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 dickson 所有!转贴必须注明作者、出处和本声明,并保持内容完整
toyota camry 2004 换全部刹车片多钱?

发表于 2011-1-1 00:32 |显示全部楼层
此文章由 7jf 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 7jf 所有!转贴必须注明作者、出处和本声明,并保持内容完整
换Boxer 引擎正时皮带,拆飞轮时要用到一个套筒拧中心螺丝同时用另一个专用工具反向别住飞轮。如果是手动挡车是否用第五挡别住即可,不用那个专用工具了?谢谢!
做个看帖不回的足迹好网民。

退役斑竹 2008年度奖章获得者

发表于 2011-1-1 00:56 |显示全部楼层
此文章由 大球球 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 大球球 所有!转贴必须注明作者、出处和本声明,并保持内容完整
原帖由 7jf 于 2011-1-1 00:32 发表
换Boxer 引擎正时皮带,拆飞轮时要用到一个套筒拧中心螺丝同时用另一个专用工具反向别住飞轮。如果是手动挡车是否用第五挡别住即可,不用那个专用工具了?谢谢! ...

我觉得悬.这个螺丝的扭距肯定不小.我不清楚具体数字,不过估计100到200牛米肯定要的.你的发动机的最大扭力估计也在2-300牛米之间,可以想象5挡即使卡的住承受的力量也不小.

发表于 2011-1-1 01:22 |显示全部楼层
此文章由 leo_melbourne 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 leo_melbourne 所有!转贴必须注明作者、出处和本声明,并保持内容完整
请问楼主,我申请了一个Personalise的车牌,但是我的车现在write off了,我如果再买一辆新车的话,我以前的那个Personal车牌还能用吗?

发表于 2011-1-1 09:58 |显示全部楼层

回复 2# 的帖子

此文章由 elsewhere 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 elsewhere 所有!转贴必须注明作者、出处和本声明,并保持内容完整
cost for the pads depend if you want to use toyota or aftermarket pads. toyota pads would generally cost more but fit better & produce less brake dust. I can find out & let you know.
Advertisement
Advertisement

发表于 2011-1-1 10:02 |显示全部楼层

回复 3# 的帖子

此文章由 elsewhere 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 elsewhere 所有!转贴必须注明作者、出处和本声明,并保持内容完整
providing you have the tool to hold the crank pulley in place, engage 5th gear to crank the motor which will use adverse torque to crack & loosen off the crank pulley. failing that, a powerful impact gun with full air compressor charge should also do the trick! if you are going to use engine load to crack the bolt, don't hold the ignition for long. just do it in short bursts or it may burn out the starter motor.

发表于 2011-1-1 10:03 |显示全部楼层

回复 5# 的帖子

此文章由 elsewhere 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 elsewhere 所有!转贴必须注明作者、出处和本声明,并保持内容完整
yeh you can.. just need to inform vicroads to transfer the custom plate over from the old car to the new one.
www.vicroads.vic.gov.au

发表于 2011-1-1 14:10 |显示全部楼层
此文章由 7jf 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 7jf 所有!转贴必须注明作者、出处和本声明,并保持内容完整
多谢LZ和版主。

发表于 2011-1-1 16:51 |显示全部楼层
此文章由 韬光养晦 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 韬光养晦 所有!转贴必须注明作者、出处和本声明,并保持内容完整
如果选06年-07年的 Mazda 3 or 6 & Honda的civic , 1.5万以内,综合考虑看

请问这3款哪款最好,楼主帮分析分析,有加分

发表于 2011-1-1 18:02 |显示全部楼层

回复 10# 的帖子

此文章由 elsewhere 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 elsewhere 所有!转贴必须注明作者、出处和本声明,并保持内容完整
best thing would be to drive all cars and see which one 'feels'  the best to you. I would be happy with any one of those. for long term reliability, I would choose the honda over mazda as they just do not break down as long as you look after the car. the quality of honda vehicle are also well known. haven't much experience with mazda's, but being a japanese car, I'll be surprised if they aren't as reliable as honda.

评分

参与人数 1积分 +8 收起 理由
★阳光小帅★ + 8 06年civic是泰国产的,马自达 保养费挺贵的,赶 ...

查看全部评分

Advertisement
Advertisement

发表回复

您需要登录后才可以回帖 登录 | 注册

本版积分规则

Advertisement
Advertisement
返回顶部