|
|
RE: Post your resume here, I will try help you
此文章由 afajufeng 原创或转贴，不代表本站立场和观点，版权归 oursteps.com.au 和作者 afajufeng 所有！转贴必须注明作者、出处和本声明，并保持内容完整
老大卫 发表于 2008-6-18 11:46 
Personal Comments:
☆ Over 5 years experience of electronics design;
☆ Advanced hardware and softwa ...
Personal Comments:☆ Over 5 years experience of electronics design;☆ Advanced hardware and software knowledge of electronics product for automotive;☆ Ability of CAD tools application for circuit design and PCB layout, such as Mentor Graphics DxDesign, Zuken Visula, CR-5000, Cadvance, and Protel;☆ Quick learning and adaptation;☆ Cooperation and teamwork spirit;☆ Well organized;☆ Communication skills in English, Mandarin and JapaneseQualification / Education:2005 Professional Electronics EngineerENGINEERS AUSTRALIA19xx – Electric Information Engineer Bachelor DegreeWork Experience:2008 S AustraliaWork description: Product test, PCB modificationSoftware debug for radio/monitor system, motor control system and fixed issues about the programs by C/C++2005-2007 Y ChinaElectronics Engineer in Product Development Department20xx-20xx main designer for D, which was redesigned for cost down about 25%Work description: 1 Achieve power supply and front panel circuit calculation, worst case analysis;2 Analogue and digital circuit design including micro controller circuit, external electrical interface circuit, audio circuit including iPod interface design via CAD tool DxDesign;3 Complete HSIS, HMI design and software test;4 EBOM, DFMEA design, write alert / design change;5 Implement tuner and audio performance tests; tuner performance improvements, Usable Sensitivity, Signal/Noise etc;6 Implement radio vibration test, high temp and low temp test and tuner performance improvements at these conditions;7 Support the production line in Portugal; solve problems of tests on line. 20xx-20xx M front panel designWork description: Front panel circuit design including key matrix and LED, LCD control circuit via CAD tool DxDesign, PCB layout via Visula.20xx Joined the design team for T which won the V Innovation Prize in 2007, it’s a radio platform with CD, Mp3, USB, SD card and has been applied in a lot of car radio projects, such as M2, F, etc.Work description: 1 Front panel circuit design including key matrix and LED, LCD control circuit via CAD tool DxDesign, PCB layout via Visula;2 CD mechanism servo board circuit design including power supply circuit, MCU circuit, USB/SDCARD interface circuit via CAD tool DxDesign, burn the software into flash and test, etc;2002-2005 P Co., Ltd ChinaElectronics Engineer in R&D Department Design Section 120xx –20xx Finished design of 2DIN after market car stereo F series which have CD/MP3/MD or CD/MP3/CASSETEWork description: 1 Front panel circuit design including key matrix and LED, LCD control circuit, motherboard PCB layout via CAD tool Cadvance;2 Fixed Beat Noise problems in the RF tuner FM and AM3 Audio (CD, MD) and Tuner (FM, AM) performance measurements4 General performance measurements, such as max power, consumption current, etc;5 EMC / EMI test, reliability tests, electrostatic destruction test; RF noise test6 Support the production line in Shanghai20xx – 20xx Worked in P in Japan as electronic engineer and trainee, and finished design of 2DIN after market car stereo F which has CD,MD.Work description: 1 Front panel circuit design including key matrix and LED, LCD control circuit, PCB layout via CAD tool CR-5000;2 Implement audio and tuner performance test;3 General performance measurements, such as max power, consumption current, etc;4 Reliability test, fixed problem in electrostatic destruction test; RF noise test, etc5 Implement EMC / EMI test.6 Support the production line in Japan.Professional DevelopmentI have attended training courses in the following:☆ DFMEA training course☆ AM FM Radio☆ CD MD DVD technologh☆ 7 Habits of Highly Effective People☆ 5S methodology
这位好像是我的老前辈啊 以前在pioneer 设计一课的? 出来喝杯咖啡如何 |
|
Kluger GX 2wd 2014款 更新 (2014-3-18) jj_1009 
楼主:Ausbear
发表于 2008-6-26 17:31
