家里的evaporative cooling不出冷风了，有人能修吗？

nicky100

牌子是Bonaire，风机没问题，水泵也有声音，但就是只出热风，怀疑是水上不去，不知道大家知道哪里能修吗？我住西边
比较急，谢谢

motorhero

出热风， 是因为水没有循环。 最可能的原因是下水阀坏了， 水箱不存水。 另外，就是你的上水阀关了。 自己上房检查一下。有问题再说。

nicky100

原帖由 motorhero 于 2009-1-13 22:46 发表
出热风， 是因为水没有循环。 最可能的原因是下水阀坏了， 水箱不存水。 另外，就是你的上水阀关了。 自己上房检查一下。有问题再说。

去年用的时候都很好，下水阀坏了会一直不停的漏水吗？，上水阀从来就没动过啊，不知道这2个水阀在UNIT里面还是在屋顶的隔层里面啊？

涵妈妈

先看看你的控制开关上显示的是COOL 还是 VENT.如果是VENT，那是除湿的。

motorhero

但是水会从房檐的下水槽走， 你看不到， 或许可以听到上/下水声音。 最简单的办法就是上屋顶看看， 水箱有水， 说明泵坏了， 水无法循环， 水箱无水， 就是上/下水阀部工作。水阀在屋顶。 在那个box下面。

[ 本帖最后由 motorhero 于 2009-1-14 11:34 编辑 ]

nicky100

原帖由 motorhero 于 2009-1-14 11:32 发表
但是水会从房檐的下水槽走， 你看不到， 或许可以听到上/下水声音。 最简单的办法就是上屋顶看看， 水箱有水， 说明泵坏了， 水无法循环， 水箱无水， 就是上/下水阀部工作。水阀在屋顶。 在那个box下面。

谢谢了，从侧边把PADS拿下来下面就直接看的到有水对吗？我开水泵能听到水泵工作的声音，估计水泵因该没问题，剩下的就是水阀了， 水阀坏了自己好修玛？

simond

发现我家的Breamer Evap Coolling 出风没有以前凉了，2年前刚换过Water Pump，一年每用多少天，准备找人修一下。 同时做下研究发现很多家有同样问题。

下面他和帖子报了很多问题及解决方法。可能有用！

http://forums.whirlpool.net.au/archive/1371841

80% problems are due the pump. Normally it is not the motor failure, but being out of balance of the shaft. When it is on, you can touch the shaft, and probably the pump will spin with certain strugles. You know what. There is a special part which is called slinger washer which is parently to spin off the water from the motor, but actually it works as a positioning part holding the shaft in the right middle, so the water fan can spin with the necessary balance. however with time the rubber slinger get aged easily, and break off. why use rubber slinger? coz they want to suck your money for replacing the pump, unfortunately these days the motor can last too long, so they have got the shit rubber slinger on to work the trick out so-called maintenance work. Trust me the evaparating cooling system is a low end technology stuff, nothing advanced, just basic electricity and mechanics. It should last very long without touching it. This is 21st century, my mates, most manufactured stuff in old technology are quite reliable...

what you should do is 1. buy a new pump and install it which costs you 107 AU dollars for the new pump probably with the rubber slinger as well, and it actually only worths 20 Chinese yuan RMB (5 dollars) from Chinese factory. Yes the rubber slinger is installed specially for Australian customers as they ordered, rather than the original stainless steel ring.
or 2. cut a milk bottle cap in a perfect size of the round seat (a round pocket just above the water fans, designed for the original metal ring), burn a hole with a big nail in the right centre of the round plastic, cut the rim though to the centre and put it on the shaft. And then push down to the seat firmly, make sure it is not loosely hang around. It will spin perfectly again, but the hole may get bigger by friction, and out of balance again, if so you can make another one. that is it.
You know if you can make a metal ring, that will be perfect. but you don't have the machine, and our installers/trademen just know this. Remember, the new pump you buy may still have the shit rubber slinger. Enjoy your life in Australia...a lot of tricks set by our greedy people, and we still protect the market and jobs for them to get easy money, being richer than scientists, professors, engineers and....sigh

红宝石小屋

邻居的水冷刚刚三天前坏掉
也不知道几岁，反正不年轻，
房东说需要几千块维修